Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations and exclusions may not apply to you. This limited warranty is issued and accepted in lieu of all other expressed warranties, and expressly excludes liability for consequential damages. In the event of a claim under this warranty, written notice must be given to the originating plant of the WBP goods at the address shown hereon. Liability under this warranty is limited to supplying new material without charge, or at manufacturers of WBP option, to a refund of the purchase price. Manufacturers of WBP do not warrant its products to be suitable for any purpose or use other than for which they were intended. Manufacturers or Western Blended Products (WBP) warrants its products to be of merchantable quality and suitable for the general purpose for which they were intended, when applied in accordance with WBP instructions. Marvel Fix shall be kept indoors or if stored outdoors, shall be adequately covered to keep dry and be stored off the ground. Do not apply Marvel Fix if conditions are expected to be above or below the specified temperature range within 24 hours of application.ġ2 months in original package properly stored. Do not apply to surfaces that are contaminated with bond breakers, oils or other matter that may affect the performance of the product. The recommendations of the finish coat manufacturer shall be followed regarding base coat preparation, acceptable pH levels, bonding, application and curing of their finish.ĭo not add accelerator, air entrainment or other admixtures to Marvel Fix without written permission from an authorized manufacturer of Western Blended Products.ĭo not apply Marvel Fix on surfaces sloped less then 30 degrees or surfaces that are below grade or subject to hydrostatic pressure.ĭo not apply when surface or ambient temperatures are at or below 40✯ / 4.4✬ or above 100✯ / 34✬. Environmental conditions such as heat, wind and low humidity will require additional curing.Ī variety of finishes such as standard acrylic paints, textured acrylic finishes or elastomeric coatings may be applied over Marvel Fix. The product requires a minimum of forty-eight (48) hours moist curing. Skim coat entire surface as described above. Feather the edges to blend into the repaired substrate. Trowel Marvel Fix over the top and another 6” to 8” in all directions from the repaired area. Marvel Fix may be directly troweled over hairline cracks in cement brown coats before the application of a skim coat.įor cracks larger then hairline (1/64”) or 'dynamic' cracks, work Marvel Fix into the crack. Mix thoroughly until a creamy, smooth consistency is achieved.Īpply 1/16” thick Marvel Fix with a steel trowel over portland cement, concrete or masonry surfaces. Use a low speed drill and mixing blade, and gradually add Marvel Fix into the container. In a clean container, add the amount of clean potable water required for the desired application. It is also recommended to increase the thickness as needed when repairing hairline cracks. Porosity of substrates will affect the coverage. Marvel Fix is available in a smooth aggregate presentation.Ĭoverage at 1/16” is approximately 120 square feet per bag. Marvel Fix is packaged in 50 lb / 22.7 kg sacks. Skim coating directly over portland cement plaster, masonry or concrete. Patching hairline cracks in portland cement plaster, masonry or concrete. Leveling, Repair & Skim Coating (Smooth) of tilt up poured-in-place panels. Available in Gray and White bases, Marvel Fix is perfect for the following scenarios: Marvel Fix is used for architectural repairs, patching and leveling of a variety of surfaces. Add it gradually while continuing to stir until the correct mix is achieved.Marvel Fix is a multi-use polymer modified cement-based compound designed to smooth, repair, patch and leveling concrete, stucco and masonry surfaces. Use only clear water suitable for drinking. Measure the dry ingredients using a coffee can or marked bucket, and blend them by stirring with a shovel or large mason`s trowel before adding water. If three layers of stucco are to be applied, prepare the first layer by combining one part Type M cement (a mixture of Portland cement and lime) and three parts masonry sand with enough water to produce a smooth, easily spread material that neither crumbles when squeezed nor slumps when troweled into a mound. Blow or brush away dust and other particles. Masonry and concrete usually do not require reinforcing material. If reinforcing material beneath the stucco is damaged, replace it by fastening metal-mesh stucco lath (available from building and masonry supply stores) over it, using galvanized staples installed by hammering. Use a hammer and cold chisel and wear goggles and heavy work gloves for protection. Begin by chipping away all loosened stucco.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |